ECHOGEAR
EGLF2 Full Motion TV Wall Mount
TV mount
From
$114.99
ECHOGEAR EGLT3 Tilting TV Mount
A tilting mount for 40 to 90 inch TVs that holds up to 135 lb and tilts 10 degrees.
Where to buy
Also check
Prices change. Each shows when it was last checked. We may earn a commission when you buy through these links; it never affects what we recommend. Amazon prices are not displayed.
The verdict
A good match for a large TV hung a little above eye level, including over a fireplace, where a few degrees of downward tilt helps. It does not swivel or extend. Steel stud walls need an extra hardware kit.
The EGLT3 is a tilting wall mount from ECHOGEAR for 40 to 90 inch TVs. It is rated for up to 135 lb, tilts up to 10 degrees, and fits VESA patterns from 200 x 100 to 600 x 400 mm. The extra-wide wall plate spans more than 24 inches so it can reach wide stud spacing, and the mount can be leveled after the TV is hung. It sits 2.3 inches from the wall.
Strengths
- Tilts up to 10 degrees to cut glare and angle the screen down.
- Rated for up to 135 lb, UL certified per the maker.
- The wall plate spans more than 24 inches and the mount slides sideways for centering.
- Can be leveled after the TV is on the wall.
Weak spots
- Tilt only, with no swivel or pull-out.
- Sits 2.3 inches from the wall, more than a fixed mount.
- Steel stud walls need extra hardware sold separately.
Great for
- Above-fireplace or higher-than-eye-level installs
- Large TVs with 16 inch or 24 inch wood studs
Skip if
- Rooms where the TV must swivel toward the seating
- TVs with VESA patterns smaller than 200 x 100 mm
Full specifications
From the manufacturer unless noted. Shown for this model.
Fit
- Mount typeFixed mounts sit flattest. Tilting helps with glare. Full-motion lets you aim the TV at different seats. Pull-down mounts bring a high TV down to eye level.
- Tilting
- Smallest VESA width
- 200 mm
- Smallest VESA height
- 100 mm
- Largest VESA widthVESA is the screw-hole pattern on the back of a TV. The mount’s range must include your TV’s pattern.
- 600 mm
- Largest VESA height
- 400 mm
- Weight capacity
- 61.2 kg
- Smallest TV size
- 40 in
- Largest TV size
- 90 in
Install
- Wall types
- Wood stud, Concrete
- Stud spacing
- 16 in or 24 in wood studs
- Post-install leveling
- Yes
Motion
- Depth from wall (closest)
- 58.4 mm
- Tilt range
- 10 degrees
Primary source: echogear.com
Setup notes
- Works with the listed VESA patterns from 200 x 100 up to 600 x 400 mm and TVs up to 135 lb.
- Wood studs at 16 in or 24 in and concrete walls work out of the box; steel studs need extra hardware.
Questions
How much can the EGLT3 tilt?
ECHOGEAR lists up to 10 degrees of tilt, and says it is no-tool to adjust.
What is the weight limit of the EGLT3?
The maker gives 135 lb, about 61.2 kg, and says the mount is UL certified to hold four times that amount.
Can the EGLT3 be installed on steel studs?
Not out of the box. The maker says wood and concrete walls work with the included hardware and sells a steel stud kit separately.
More tv mounts
Sources for this page
Last reviewed Nov 9, 2026. Spotted an error? Tell us.